When Do You Need Waterproofing?

Waterproofing may be required as a preventive measure before a problem occurs or as a corrective solution after signs of water ingress have appeared.

Some of the main situations that require a roof inspection include:

  • Rainwater leaking into the building.
  • Water remaining on the roof for extended periods.
  • Damp patches appearing on ceilings or walls.
  • Peeling paint or damaged finishes caused by moisture or water ingress.
  • A new roof that needs protection before the remaining finishes are completed.
  • An existing waterproofing layer that needs to be assessed before relying on it.

Where Is Waterproofing Used?

The installation method varies according to the element being protected and the way it is exposed to water.

Waterproofing can be used on concrete roofs exposed to rainfall and standing water. Suitable systems may also be used on certain metal roofs when the product specifications permit this application.

Other areas, such as bathrooms or water tanks, may require waterproofing systems specifically designed for their intended use, site conditions, and technical requirements.

A material that performs successfully on a concrete roof is therefore not automatically suitable for every other waterproofing application.

Roof Waterproofing Installation Process

Once the appropriate system has been selected, installation follows a clear sequence because the quality of the final waterproofing layer depends heavily on the work completed before it is applied.

1.

Roof Inspection

Leakage areas, cracks, and existing issues are identified while the overall condition of the roof and its readiness for the work are assessed.

2.

Roof Cleaning

Dust, debris, concrete protrusions, and any materials that could affect adhesion or continuity of the waterproofing system are removed.

3.

Repairing Existing Defects

Issues that form part of the surface preparation requirements are addressed to ensure that the roof is suitable for the selected system before application begins.

4.

Checking Roof Slopes and Drainage

Water flow, areas of ponding, drainage outlets, corners, and floor-to-wall junctions are inspected because these details are important when installing roof waterproofing.

5.

Applying Primer When Required

If the selected system requires a primer, the appropriate product is applied and the manufacturer’s drying and application requirements are followed before proceeding to the next stage.

6.

Installing the Waterproofing Layers

Membrane rolls or the approved waterproofing system are installed according to their specifications, with particular attention to overlaps, corners, drainage outlets, and other details that affect the continuity of the waterproofing layer.

7.

Inspecting the Waterproofing Before Covering

The completed waterproofing layer is inspected for continuity, and any observations are addressed before protective layers or finishes are installed over it.

8.

Water Testing When Appropriate

When water testing is suitable for the selected system and site conditions, it is carried out using the appropriate procedure before the work is approved and the following stages begin.

Why Do Roof Slopes and Drainage Matter Before Waterproofing?

The purpose of waterproofing is to reduce water penetration, but it does not eliminate the need for proper drainage design.

Low areas that retain water or problems with drainage outlets can cause water to remain on the roof for extended periods. For this reason, roof slopes and drainage points are reviewed before the waterproofing system is approved.

The objective is not simply to cover the roof with a waterproof material, but to install the system over a suitable base that allows it to perform according to the project design.

An inspection may show that water ingress is not caused by the protective layer alone and that the roof first requires a broader assessment of its overall condition, existing layers, or multiple details affecting how the project should proceed. In this situation, we do not install a new system directly over the existing condition. Instead, the project is referred to Roof Insulation so the roof can be evaluated as a complete system and the required work can be properly sequenced before installation continues.

Frequently Asked Questions About Waterproofing

What Is the Best Waterproofing System for Roofs?

There is no single product that is best for every roof. The appropriate system is selected according to the roof type, water exposure conditions, intended use, project requirements, and technical specifications.

Can New Waterproofing Be Installed Over an Existing Waterproofing Layer?

This decision should not be made before an inspection. The existing layer must be assessed for condition, adhesion, and compatibility with the new system. Some projects may require partial removal or treatment before installation.

Are Bituminous Membranes Better Than Liquid Waterproofing?

Each system has different applications and requirements. The choice between bituminous membrane rolls and liquid-applied waterproofing depends on the roof characteristics, project details, and required specifications rather than one system being universally better than the other.

Can a Roof Be Waterproofed After a Leak Appears?

Yes, waterproofing can be installed after leakage occurs, but the source of the leak must first be identified and any defects requiring treatment should be addressed before the new system is installed.

Is Waterproofing Tested After Installation?

When water testing is appropriate for the selected system and site conditions, it may be carried out before protective layers or finishes are completed, together with direct inspection of the waterproofing layer.

Request a Waterproofing Inspection Before the Damage Gets Worse

If damp patches or leaks appear after rainfall, or if you are preparing a new roof and want to protect it before problems occur, the correct first step is to assess the roof condition rather than selecting a waterproofing material at random.